How To Repair A Hole In A Textured Wall

Download Commodity

Learn how to patch a large hole using a wall patch or piece of drywall

Download Article

When you lot have a big hole in your wall, it's easy to patch information technology up and so you can paint over it. Use a wall repair patch to hands cover up holes upward to half dozen in (fifteen cm) in diameter. Cut larger holes into a square or rectangle, and so create a patch out of drywall and attach it to the inside of the hole. Cover up either type of patch with joint compound and sand it to blend it into the surrounding wall.

1. 1

   Cut abroad and remove any loose debris and jagged paper edges from the pigsty. Pull off any dangling pieces of drywall and plaster. Utilise a utility knife to cut along the edges and remove any jagged pieces of drywall paper.^[1]

   • The goal is to clean the pigsty up enough that the wall repair patch volition sit apartment on elevation of information technology with no loose debris or ragged paper edges pushing against it or interfering with the agglutinative.
   • This method works for holes that are upward to virtually 6 in (15 cm) in bore. Wall patches come in sizes upward to 7–8 in (18–20 cm) in diameter, and the patch needs to exist slightly bigger than the pigsty to attach to the wall around it.

2. two

   Create a repair patch that is about 1 in (two.5 cm) bigger than the hole. Use precipitous scissors to cut a wall repair patch and so that it is approximately 1 in (ii.5 cm) taller and 1 in (2.5 cm) wider than the pigsty in the wall. This volition allow information technology to adhere firmly to the intact wall surrounding the hole.^{[two] [iii]}

   • You lot tin can buy wall repair patches in different sizes, and so you can besides just buy one that is the correct size.
   • Wall repair patches are made of a mesh material that is able to support spackling on top of it.

   Advertisement

3. 3

   Peel the bankroll off the patch and stick it over the pigsty. Remove the lining from the agglutinative on the back of the patch. Center it over the hole and press downwardly firmly around all the sides to stick it to the wall.^[4]

   • You lot don't need to wait for the patch to dry on the wall, the agglutinative patch will be sealed and ready to cover up as soon as you stick it on.

4. iv

   Use a sparse layer of articulation compound to completely cover the patch. Use a putty pocketknife to spread a layer of joint compound over the unabridged patch so you can't see the mesh anymore.^[5] Overlap the coat onto the surrounding wall by about 1 in (2.5 cm).^[6]

   • Overlapping the joint compound onto the surrounding wall will make information technology easier to blend in so the patch isn't noticeable.

   Tip: Joint compound is besides known equally drywall mud or merely mud.

5. five

   Allow the articulation chemical compound dry out for 24 hours. Expect until the compound is completely dry out before sanding. This usually takes up to 24 hours, merely drying times vary depending on the temperature and humidity.^[vii]

6. half dozen

   Sand the patch with fine-dust sandpaper until information technology is smooth. Attach a piece of 120- to 150-grit sandpaper to a sanding block or just sand by mitt. Lightly sand the entire patch down until information technology is shine and blends in with the surrounding wall.^[eight]

   • Don't sand likewise difficult or you might betrayal the mesh patch below the compound. Just focus on smoothing out any rough spots and blending it in with the wall.

7. 7

   Repeat the procedure for a 2d coat of joint chemical compound. Apply some other thin layer of articulation compound over the patch and the surrounding wall. Let information technology dry for 24 hours, then sand it down with fine-grit sandpaper until it is shine and blends in with the wall.^[9]

   • If you want to make the joint compound textured, you can dab it with a sponge while it is still wet or use a textured paint roller to apply a terminal sparse layer of watered-downwardly compound.
   • If you're ready to paint the wall, use a h2o-based primer to prime number the patch before applying wall paint.

Advertisement

1. 1

   Cut the hole into a great square or rectangle. Use a utility pocketknife or drywall saw to cutting the jagged hole into a square or rectangle with straight edges.^[10] This will allow yous to create a precisely-shaped patch for the drywall and install it hands.^[eleven]

   • This method works for holes that are bigger than 6 in (xv cm) in bore.

2. 2

   Create a patch out of drywall that is 2 in (v.1 cm) taller than the hole. Cut a piece of drywall to the aforementioned width as, or just slightly wider, than the hole but a full 2 in (5.1 cm) taller. The extra height will let you to attach it to the inside of the hole with adhesive.^[12]

   • Yous can purchase small pieces of drywall for patching that are 2 ft (0.61 m) in diameter.

   Tip: If you don't have a scrap piece of drywall to make a patch out of, you could use a ¹⁄₂  in (ane.3 cm)-thick slice of flake wood instead.

3. 3

   Put a spiral through the middle of the patch to brand a handle. Twist or push button a 1.five in (3.eight cm) or two in (5.1 cm) drywall screw through the centre of the drywall patch you made so there is nevertheless enough sticking up for you to grab onto. This will let yous to hold it against the inside of the hole while you let the adhesive dry.^[xiii]

   • If you don't accept a drywall screw you can utilize a wood screw instead.

4. 4

   Apply construction adhesive to the bottom and top edges of the patch. Put a zig-zag of construction adhesive along the top i in (ii.5 cm) of the patch. Do the aforementioned for the lesser one in (two.5 cm).^[14]

   • For example, yous can utilise a construction agglutinative like liquid nails.

5. 5

   Insert the patch into the hole and use the screw to concord it in identify while it sets. Pick upwards the patch past the spiral and tilt it until you can insert it into the hole. Straighten it out so it is oriented correctly and pull it towards the inside of the wall so the adhesive makes contact. Concur it in place for about fifteen minutes until the adhesive has dried enough to hold information technology in place.^[15]

   • You can either push button the screw through the patch into the wall void once it has dried or unscrew it and pull it out.

6. six

   Let the agglutinative cure for upwardly to 24 hours before proceeding. Refer to the manufacturer'southward instructions for the adhesive yous used to go the verbal drying time. Leave it to cure in identify at least overnight and up to 24 hours.

   • This will ensure that the patch is secured strongly in place and volition be able to support the weight of joint compound.

7. seven

   Put a thick layer of articulation chemical compound on top of the patch to fill information technology in. Use a putty knife to apply joint chemical compound over the patch until the hole is filled to the level of the wall. Polish out the edges so the compound overlaps onto the wall past about 1 in (2.5 cm).^[16]

   • Use the widest putty knife you have to polish out the edges more hands.

8. 8

   Let the offset layer of articulation chemical compound dry for 24 hours. Go out the patch to dry for about 24 hours so it is totally cured before sanding. This is especially important since this layer is relatively thick and it volition take longer to dry than a thin layer of joint compound.^[17]

   • If you don't let the joint compound dry completely, in that location will be moisture trapped inside that can crusade the patch to fall apart.

9. 9

   Sand the joint compound shine afterward it is dry out. Use 120- to 150-grit sandpaper to smooth out the first layer of joint chemical compound. Sand by hand or using a sanding block.^[18]

   • But try to become rid of any crude patches and blend the edges into the surrounding wall. You volition exist repeating the process, so don't worry about getting it perfect.

10. 10

    Apply 1-ii additional thin layers of joint compound to blend the patch in. Apply a putty pocketknife to apply some other thin glaze over the patch and the surrounding 1 in (2.5 cm) or then of the wall. Let it dry out overnight, then sand it downward with 120- to 150-dust sandpaper to smooth it out and blend it in with the wall. Repeat the steps for another layer if you lot want to blend it in even more.^[19]

    • If yous need to make the joint compound textured to match the rest of the wall, use a textured roller to apply the watered-downwards compound as the last layer or dab the final layer with a sponge while information technology is however moisture.
    • Remember to permit the final coat dry for at least 24 hours before priming the patch and painting the wall.

Advertizement

Enquire a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Advertisement

Things Y'all'll Need

• Wall repair patch
• Pair of scissors
• Utility knife
• Putty pocketknife
• Joint chemical compound
• Sanding cake (optional)
• 120- to 150-dust sandpaper

• Utility knife or drywall saw
• Piece of drywall
• Putty pocketknife
• Joint chemical compound
• Sanding block (optional)
• 120- to 150-dust sandpaper
• Drywall spiral or wood screw
• Structure agglutinative

Almost This Article

Thanks to all authors for creating a page that has been read 20,045 times.

Did this article help you lot?

Source: https://www.wikihow.com/Fix-a-Large-Hole-in-the-Wall

Share this post